1、真空回吸閥必需要安裝在全自動點膠機上，由于真空回吸功能是避免點膠機中的膠水在不點膠時還在滴漏。
1. The vacuum suction valve must be installed on the automatic dispenser, because the vacuum suction function is to prevent the glue in the dispenser from leaking when it is not dispensing.
2、點膠量的大小是由全自動雙組份打膠機在點膠進程中繼續的時刻長短來抉擇的，可以保證有滿足的膠水來粘合部件，一起可以避免膠水過多而造成的資源浪費。
2. The size of dispensing volume is determined by the duration of the full-automatic two-component dispenser in the dispensing process. It can ensure that there is enough glue to glue the parts, and it can avoid the waste of resources caused by too much glue.
3、在全自動雙組份打膠機職業中一般運用的膠水大概有硅膠、瞬間膠、厭氧膠、環氧樹脂、UV膠。
3. The general glue used in the full-automatic two-component gluing machine industry is about silica gel, instant glue, anaerobic glue, epoxy resin and UV glue.
4、針頭的規范與類別：針頭的規范會影響點膠機在點膠進程中出膠的大小和精密度,當氣壓在必定規模時，針頭的咀越大,出膠率就越大，所以要根據點膠機在出產出來產品的大小來定位點膠針頭的規范，一般針頭內徑長度保持在膠點直徑的一半,作用才是好。
4. Specification and category of needle: the specification of needle will affect the size and precision of dispensing machine in the dispensing process. When the air pressure is at a certain scale, the larger the tip is, the larger the dispensing rate is. Therefore, the specification of dispensing needle should be positioned according to the size of the products produced by the dispensing machine. Generally, the length of the inner diameter of the needle is kept at half of the diameter of the dispensing point, which is the best.

5、固化要素：關于膠水的固化，一般出產廠家已給出溫度曲線。一般在常溫下都可以固化，在實際應盡可能選用較高溫度來固化，使膠水固化后有滿足強度和硬度。
5. Curing factors: for the curing of glue, the general manufacturer has given the temperature curve. Generally, it can be cured at room temperature. In practice, higher temperature should be selected as far as possible to make the glue meet the strength and hardness after curing.
6、氣泡關于全自動雙組份打膠機在進行點膠進程中會影響產品質量，所以膠水放進去之前決對不能有氣泡.如果有氣泡就會造成點膠機出產出來的產品有許多次品，在運用中要排出膠水的空氣，以避免呈現全自動點膠機空打現象。
6. Bubble about the automatic two-component dispenser will affect the product quality in the dispensing process, so there must be no bubble before the glue is put in. If there is bubble, there will be many defective products produced by the dispenser, and the air of the glue should be discharged during the application, so as to avoid the phenomenon of empty dispensing of the automatic dispenser.
7、壓力的大小直接影響了供膠量和膠水流出的速度,膠水的流動性越差它就越稠，全自動雙組份打膠機需求的壓力就越大，所以咱們應該根據全自動點膠機在出產進程中的環境溫度以及點膠量的大小和膠水的特性來調度壓力的大小，全自動點膠機的壓力大小是經過它內部的調壓閥來進行調度的。
7. The pressure directly affects the glue supply and the speed of glue outflow, The worse the fluidity of glue, the thicker it will be, and the greater the pressure required by the full-automatic two-component dispenser. Therefore, we should adjust the pressure according to the ambient temperature of the full-automatic dispenser in the production process, the size of the dispensing amount and the characteristics of glue. The pressure of the full-automatic dispenser is regulated by its internal pressure regulating valve.
以上就是雙組份打膠機為大家做介紹的在使用過程中需要遵循什么？ 想要了解更多的雙組份打膠機的內容  請關注官網http://m.txxfj.com
The above is the double beater for you to do the introduction in the use process to follow what? To learn more about the duplicator, please pay attention to the official website http://m.txxfj.com