想要打出光滑平整的膠，我們應該注意一些什么呢？我們和濟南雙組份打膠機廠家一起看看吧！
What should we pay attention to in order to make smooth and smooth glue? Let's have a look with Jinan two-component glue machine manufacturer.
1、有好的膠，然后出膠的膠嘴要切割平整大小要和鋁合金打膠的位置大小相當；打膠時手要穩不能抖動，要一氣呵成，朝一個方向打膠，不能多次停頓。
1. First of all, there is good glue, and then the glue nozzle should be cut flat to the same size as the position of aluminium alloy gluing; when gluing, the hand should be stable and not shake, and gluing in one direction should be completed at one go, and not stop many times.
2、就是靠手感,打多了，有經驗了，自然就摸索出來了。
2. It depends on the feeling of the hand. If you play more and have experience, you will find out naturally.
3、削個45°角，口的大小看縫口大小定，這樣能一次打好膠，外觀漂亮，還節約膠。
3. Cut a 45 degree angle, the size of the mouth depends on the size of the seam, which can make a good glue, beautiful appearance, but also save glue.
4、切口呈45度坡角,這樣打的膠平整光滑,不帶印紋。
4. The incision is 45 degrees inclined, so that the glue is smooth and smooth without printing.
5、用壁紙刀斜削，膠嘴一般上面都有幾個刻度，盡頭的是小嘴，往下依次變大，你可以根據自己的需要的大小去削，可以先從小削起。
5. Cut obliquely with wallpaper knife. Generally, there are several scales on the rubber nozzle. At the end of the nozzle, it becomes bigger in turn. You can cut it according to your own size. You can start with the smallest one.

在操作的時候，我們要注意：
In operation, we should pay attention to:
1、重要的是右手握扳機，擠出玻璃膠的力度一定要均勻。要用我們平常所說的“陰力”，也就是保持一定的力量，但不能時大時小。要一氣呵成，不能擠一擠，停一停，否則玻璃膠斷斷續續，又或者一大一小。因?yàn)橥ǔ２Ａz剛被擠出噴嘴的時候，都是比較大的球狀的。如果塊大塊小，就只能后面用涂抹的方法搽平了。
1. It is important to hold the trigger in the right hand and extrude the glass glue evenly. We should use what we usually call "negative force", that is, to maintain a certain strength, but not when big or small. If you want to finish at one go, you can't squeeze and stop. Otherwise, the glass glue will be intermittent, big or small. Usually when the glass glue is just extruded from the nozzle, it is larger spherical. If the block is large or small, it can only be smoothed with a smear on the back.
2、左手控制嘴，一定要讓嘴的斜口緊貼縫隙，不能搖晃。
2. Left-hand control mouth, must let the mouth bevel close to the gap, can not shake.
3、腳步要穩，預先校準移動的距離，盡可能不要過多的移動腳步，適當將雙腿分站得開一點，這樣可以保證用上身平移或者轉腰加手上功夫，擠出玻璃膠的直線。如果腳步走動過多，勢必影響擠出玻璃膠的穩定性。
3. Step steadily, pre-calibrate the distance of movement, as far as possible do not move too much footsteps, appropriate legs stand a little open, so as to ensure the use of upper body translation or waist rotation plus hand effort, extrusion of glass glue straight line. If the footsteps move too much, it will inevitably affect the stability of extruded glass glue.
4、調節呼吸。不要大呼大吸，保持小幅度的呼吸，甚至短暫屏氣，讓上身不要因?yàn)楹粑鼡u晃過大。
4. Regulate breathing. Don't breathe heavily, keep a small breath, or even hold your breath for a short time. Don't let your upper body shake too much because of breathing.
以上的精彩內容由濟南雙組份打膠機的小編整理所得，以上內容均來源于網絡，假如大家由不同的意見，歡送大家到我們的官網：http://m.txxfj.com！給我們留言評論，我們會定期給大家一個回復！
The above wonderful contents are obtained from the small arrangement of Jinan two-component glue machine. The above contents are all from the network. If you have different opinions, welcome you to our official website: http://m.txxfj.com! Leave us a comment and we will give you a regular reply!