1、A組份提膠由電動齒輪泵提供，經管道輸送至油壓驅動的A膠高壓柱塞泵增壓。B組份提膠由氣動往復泵提供，經管道輸送至油壓驅動的B組分高壓柱塞泵增壓。
　　1, A component extract is supplied by electric gear pump, and the A rubber high pressure plunger pump is pressurized by pipeline to oil pressure. B component extract is supplied by pneumatic reciprocating pump, and the B component high pressure plunger pump is pressurized by pipeline to oil pressure.
　　A、B膠的體積比例由雙組分比例調節機構調整，然后，同時送入打膠機混合器，混合器由36節以上混合裝置組成，雙組份膠充分混合后到達涂膠槍?zhuān)瑥哪z嘴噴出，涂布于中空玻璃的邊緣進行封邊。膠嘴設有啟動快速關閉閥，用以準確控制出膠時間。
　　The volume ratio of A, B glue by the two-component proportion regulating mechanism, and at the same time, into the glue mixer, the mixer is composed of 36 sections above the mixing device, two-component adhesive after mixing to glue gun, glue from the spout, the edge is coated on the insulating glass edge. The glue nozzle has the start quick closing valve, which is used to accurately control the glue time.
　　2、雙組份供膠機主要有A組份提膠泵、B組份提膠泵， A、B膠增壓裝置，高壓柱塞泵，A、B膠泵連接裝置，雙組分比例調節機構，高壓出口安全分流裝置，液壓控制系統，氣動控制系統及電器控制系統等組成。

　　2, two-component glue machine mainly has A components and B components of gel extraction pump rubber pump, A, B glue pressurizing device, high pressure piston pump, A pump, B glue connecting device, double component ratio adjusting mechanism, a high pressure outlet safety shunt device, hydraulic control system, pneumatic control. System and electrical control system.
　　3、供膠機的B組份膠出口處設有放泄閥，可以放氣或泄壓回流用，同位置還設置了超壓回流的安全裝置。在機頭上進入混合器之前設有關斷球閥和單向止回閥，防止A、B組份膠互串，造成固化而堵塞通道。
　　3. There is a vent valve at the B glue outlet of the glue feeder, which can release gas or pressure reflux, and also set a safety device for overpressure reflux in the same position. Before entering the mixer, a shut-off ball valve and a one-way check valve are set up to prevent the A and B components from interconnected, causing curing and blocking the channel.
　　4、A、B組份體積比例調節由雙組分比例調節機構完成。 A、B組份比例分配比的調節主要靠調節高壓泵前端連軒上的滑塊，向上調B膠出膠少，向下調B膠出膠多。滑塊中心距上端軸中心線16.4cm時，A/B膠的比例為10比1。
　　The volume proportion of the 4, A and B components is adjusted by the double component proportional regulation mechanism. The proportion distribution ratio of A and B is regulated mainly by adjusting the slider on the front of the high pressure pump, less glue out of B glue, and more glue out of B. When the center of the slider is from the center line of the upper end axis 16.4cm, the proportion of A/B glue is 10 to 1.
　　本文由雙組份打膠機為您提供，我們的網站是:http://m.txxfj.com我們將以全心全意的熱情為您提供更優質的服務，歡迎您的訪問！
　　This article is provided by two component glue machine. Our website is: http://m.txxfj.com, we will provide you with better service with wholehearted enthusiasm, welcome your visit.