電子產品一直是全自動點膠機商家的主要輸出范圍，全自動點膠機商家想要搶占電子產品的市場，應牢記的就是根據當下需求來進行生產經營。
Electronic products have always been the main output range of automatic dispensers. In order to seize the market of electronic products, automatic dispensers should bear in mind that production and operation should be carried out according to the current demand.
影響點膠效果的要素通常有點膠量的大小，點膠壓力，針頭大小 ，針頭與工作面之間的間隔，膠水的粘度，膠水溫度，固化溫度曲線，膠水中氣泡，需求特殊設定的流體等等，下面昌盛人員就來為大家做一個簡單的介紹，希望可以有所協助。
The factors that affect the dispensing effect usually include the size of dispensing amount, dispensing pressure, needle size, distance between the needle and the working face, glue viscosity, glue temperature, curing temperature curve, bubbles in glue, and fluid required for special setting, etc. below, Changsheng personnel will make a brief introduction for you, hoping to help.
點膠量的大小通常以為膠點直徑的大小應為產品間距的一半，這樣就能夠保證有充足的膠水來粘結組件又防止膠水過多。點膠量幾由時間長短來決議，實踐中應依據溫度和膠水的特性選擇點膠時間。

First of all, the size of the dispensing amount usually assumes that the size of the glue dot diameter should be half of the product spacing, so as to ensure that there is enough glue to bond the components and prevent excessive glue. In practice, the dispensing time should be selected according to the temperature and the characteristics of the glue.
其次點膠壓力方面，通常壓力太大易形成膠水溢出、膠量過多；壓力太小則會呈現點膠斷續現象和漏點，從而招致產品缺陷，所以需求依據環境溫度和膠水粘度等要素停止調理自動點膠機。
Secondly, in terms of dispensing pressure, too much glue is easy to form when the pressure is too high; if the pressure is too small, it will lead to intermittent dispensing and leakage, which will lead to product defects. Therefore, it is necessary to stop conditioning the automatic dispenser according to the environmental temperature and glue viscosity.
再者，點膠機針頭通常要選取針頭內徑大小為點膠膠點直徑的1/2左右的針頭，點膠過程中，應依據產品大小來選取點膠針頭。
In addition, the pinhead of dispensing machine usually needs to select the needle whose inner diameter is about 1 / 2 of the dispensing point diameter. During dispensing, the dispensing needle should be selected according to the product size.
還有，針頭與工作面之間的間隔，不同的點膠機采用不同的針頭，有些針頭有一定的止動度，因而需求把握好點膠間隔，以至每次工作開端之前應做針頭與工作面間隔的校準，即Z軸高度校準。
In addition, the distance between the needle and the working face is different. Different dispensers use different needles, and some needles have a certain degree of stop. Therefore, it is necessary to grasp the dispensing interval and calibrate the spacing between the needle and the working face before the beginning of each work, i.e. z-axis height calibration.
除卻全自動點膠機自身的要素，膠水的粘度直接影響點膠的質量，粘度大，則膠點會變小，以至拉絲；粘度小，膠點會變大，進而可能滲染產品，而膠水溫度應為23℃～25℃；環境溫度對膠水的粘度影響，溫度降低粘度提升，出膠流量相應變小，更容易呈現拉絲現象。膠水固化溫度曲線消費廠家已給出，在實踐應盡可能采用較高溫度來固化，使膠水固化后有足夠強度。
In addition to the elements of the automatic dispenser itself, the viscosity of the glue directly affects the quality of the dispensing. If the viscosity is high, the glue point will become smaller and even wire drawing will occur; if the viscosity is small, the glue point will become larger, and then the product may be dyed, and the glue temperature should be 23 ℃ - 25 ℃; the environmental temperature will affect the viscosity of the glue, the temperature will decrease, the viscosity will increase, and the glue flow will be reduced accordingly, which will make the drawing phenomenon easier 。 The curing temperature curve of glue has been given by the consumer. In practice, it should be cured at a higher temperature as much as possible, so that the glue has enough strength after curing.
另外膠水一定不能有氣泡。一個小小氣泡就會形成許多產品沒有膠水；每次中途改換膠管時應排空銜接處的空氣，避免呈現空打現象。
In addition, the glue must not have bubbles. A small bubble will form a lot of products without glue. When changing the rubber tube midway, the air at the joint should be emptied to avoid empty hitting.
電子產品越來越重視用戶體驗，輕薄化就是其中一個主要的發展趨向。招致電子元件越來越小，元件的大小在1mm左右曾經很常見。在電路板上的元件之間的間隔也越來越近。傳統點膠機用肉眼人工示教編程的方式曾經無法準確定位了，應用CCD成像技術，將產品放大30-50倍顯現在電腦屏幕上，停止準確定位編程才干滿足客戶的消費請求。
Electronic products pay more and more attention to user experience, and lightness is one of the main development trends. As a result, electronic components are becoming smaller and smaller, and the size of the components is about 1 mm. The spacing between the components on the circuit board is getting closer and closer. Traditional dispensing machine with naked eye manual teaching programming method has been unable to accurately locate, the application of CCD imaging technology, the product magnified 30-50 times displayed on the computer screen, stop accurate positioning programming ability to meet customer demand.
應用不同像素的CCD和鏡頭不同放大倍數，以及多種光源的組合，能夠完成十分準確的定位精度，同時能夠經過編程順應產品本身的個體誤差。
The application of CCD with different pixels and different magnification of lens, as well as the combination of various light sources, can achieve very accurate positioning accuracy, at the same time, it can be programmed to adapt to the individual error of the product itself.
響點膠精度的因素很多，自然不止上面所舉的一些，有的時候甚至是各種力量共同作用的結果。這就對點膠工藝提出了更高的要求，一方面應當盡量避免問題的出現，另一方面，問題已經出現的時候需要根據實際生產操作流程找到原因，解決問題。
There are many factors affecting the accuracy of dispensing. Naturally, it is not only some of the above mentioned, but sometimes even the result of the joint action of various forces. This puts forward higher requirements for dispensing process. On the one hand, problems should be avoided as far as possible. On the other hand, when problems have appeared, the causes should be found and solved according to the actual production process.