1、在當天機器操作完畢后要把膠管內的膠沖出，防止硬化；如果長時間不實用要注意用煤油清洗膠管和膠槍。
1. After the operation of the machine on the same day, the glue in the hose should be flushed out to prevent hardening; If it is not practical for a long time, pay attention to clean the hose and gun with kerosene.
2、雙組份打膠機使用的硅酮膠或聚硫膠要注意雜質不能過高，低質量的膠容易堵塞膠管的過濾系統，造成出膠不暢或不均勻。
2. For the silicone glue or polysulfide glue used in the two-component rubber beater, attention should be paid to that the impurities should not be too high. The low-quality glue is easy to block the filter system of the hose, resulting in poor or uneven glue delivery.
3、在更換膠的品種時要非常注意把雙組份打膠機內殘留的膠沖凈，好清洗，因為不同品種甚至的膠容易反應堵塞機器。
3. When changing the type of glue, special attention should be paid to the residual glue in the two-component beater for cleaning, because different varieties or even brands of glue are easy to react and block the machine.

4、液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調至滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍，否則B組份管路壓力將升得很高，造成安 全事故。
4. The pressure of the hydraulic station system can not be adjusted too high. According to the indoor environment temperature and other actual conditions, the pressure should be adjusted to meet the requirements of the normal glue output of the rubber nozzle and the uniform glue injection. When opening the hydraulic station, the glue gun must be opened, otherwise the pressure of component B pipeline will rise very high, causing safety accidents.
雙組份打膠機
Two component gluing machine
5、A膠提膠泵連續工作1分鐘以上沒有供膠停止，說明管路內有空氣，此時會警聲，須打開泵上管接頭再打開A膠提膠泵，直到出膠為止，停止并接好接頭，膠槍會出現有空氣的嗶嗶爆 破聲，空氣排凈就好了。
5. If the glue supply of a glue pump does not stop for more than 1 minute, it means that there is air in the pipeline. At this time, the alarm will sound. You must open the upper pipe joint of the pump, and then open the a glue pump until the glue is discharged. Stop and connect the joint. The glue gun will have a beep blasting sound with air, and the air will be drained.
6、硅酮膠B組份遇空氣會結殼，影響泵的正常工作和管路的暢通，因此，停機時B組份膠的所有通道在泄壓后均應關閉，使B組份不得接觸空氣。
6. Component B of silicone rubber will crust when encountering air, which will affect the normal operation of the pump and the smooth flow of the pipeline. Therefore, all channels of component B should be closed after pressure relief during shutdown, so that component B can not contact with air.
7、正常工作時不要斷氣源，如果發現斷氣源應停止工作。
7. Do not cut off the gas source during normal operation. If it is found that the gas source is cut off, stop working.
以上就是給大家分享的內容了，想要了解更多的精彩內容進入我們的官方網站，或者是搜索我們的關鍵詞雙組份打膠機http://linshi.jncsjx.com查找，我們會有更多的精彩內容與您分享!
The above is to share the content, want to know more wonderful content into our official website, or search our keyword two-component glue machine http://linshi.jncsjx.com Find, we will have more wonderful content to share with you!